Automatic cold-chain control for businesses that store food and other cold-chain products · wireless sensors, pre-configured kit

How it works

How KRYO HACCP temperature monitoring works

From assessment to activation: a simple process, managed entirely by us.

You don’t have to choose sensors, configure networks or learn software. Analysis, configuration and checks are our responsibility. The service integrates into your HACCP self-monitoring plan: you decide what to monitor with your consultant, we measure, alert and record.

From first contact to activation, in six steps

  1. Free assessment

    You describe your business and send us a few photos: cold rooms, fridges, display cases, the router and the layout of the production room. We need them to work out how many points to monitor, where to place the sensors and whether it makes sense to add energy consumption, doors or production room climate.

  2. Tailored proposal

    We send you a written proposal based on what you actually have, not a standard package. If you don’t need something, we don’t propose it.

  3. Shipping the pre-configured kit

    The central unit and sensors arrive already paired with each other and with your business, with instructions on where to place each sensor. Before shipping we tell you the network requirements: a free network socket on the router and Internet access for the central unit.

  4. Setting up the temperature kit

    You connect the central unit to the router with a network cable and place the wireless sensors in your fridges, cold rooms and display cases: for the temperature kit, when the installation conditions allow, no technician on site is needed. The exception is power meters that require work on the electrical panel, which must be done by a qualified electrician.

  5. Initial check and activation

    We check remotely that the central unit is reachable and that every sensor is transmitting from its position: this is where the radio coverage estimated from your photos is confirmed, and where sensors are moved if necessary. Then, together with you, we set the thresholds and the people to alert. Indicative time: same day after delivery, if the network is available and coverage is good; otherwise a few days more.

  6. KRYO works 24 hours a day

    It receives readings at regular intervals (normally every 3–5 minutes), updates the HACCP log and only contacts you when a value stays out of range or a component stops transmitting.

What’s in the kit

The central unit

The heart of the system. It receives the sensor data and sends it securely to the KRYO service. It connects to the router with a network cable, no SIM: no problems with weak Wi-Fi in the back room or the production room. If it stops communicating, the service alerts you.

The temperature and humidity sensors

Wireless and battery-powered, designed to sit inside fridges, cold rooms, freezers and display cases. One for every point to monitor. Specifications.

Doors, energy, production room, labels

Door sensors for cold rooms; power meters per unit or at the electrical panel (single-phase and three-phase); room sensor for the production room (temperature and humidity); printer for expiry-date labels. They are activated through the configuration agreed in the proposal, on the same central unit and in the same history. What KRYO monitors.

Why a cable and not Wi-Fi

In food businesses Wi-Fi is often the weak point: the cold room is at the back of the production room, the walls are thick, the router is on the other side of the building. A system that loses its connection just when it is needed is not a control system.

That is why the central unit connects to the router with a cable. The sensors communicate with the central unit by radio, on a long-range, low-power band that is generally better suited than Wi-Fi to walls and cold room doors. Actual coverage depends on materials and distances: we estimate it from your photos and verify it at activation, sensor by sensor; if a point is not covered, the sensor or the central unit is moved.

Alerts arrive where you already look

No new app to install and remember to open. Alerts arrive on Telegram and email, channels you check every day, to one or more recipients you name. WhatsApp delivery is coming. Escalation to a second contact, when nobody takes charge of the alert, is planned: we confirm it in the proposal, with the timings.

Every message says three things: which fridge, what is happening, what to do. For example: “Meat cold room: temperature above threshold for 30 minutes. Check that the door is closed and check the unit’s status.”

A temperature alert goes out after at least two consecutive out-of-range readings: with readings every 3–5 minutes, about 6–10 minutes from the start of the anomaly, plus the message delivery time. Brief door openings and normal defrost cycles do not trigger it.

What happens if something goes wrong

A continuous watch is judged by how it behaves when something fails, including the watch itself. Silence is never read as “All clear”.

Failure cases: how KRYO notices, who receives the alert, what stays in the log
What goes wrongHow KRYO noticesWho receives the alertWhat stays in the log
Door left openTemperature above threshold for several consecutive readings (with the door sensor: open beyond the set time)The named recipientsNon-conformity with start, end, duration and peak value
Unit that stops runningTemperature rising continuously, with no recoveryThe named recipients, with reminders until it is back within rangeNon-conformity in progress, reading after reading
Defrost cycle or brief openingRecovery within the unit’s waiting timeNobodyReadings recorded, not flagged as a non-conformity
Sensor that stops transmittingNo readings beyond the time limitThe named recipients and KRYO supportGap with no readings, declared as incomplete monitoring
Power or Internet downCentral unit not reachable by the KRYO serviceThe named recipients, from the KRYO serviceGap declared in the log. Sensors and central unit can hold the readings for the duration of the outage: their recovery into the log is being validated and we do not treat it as guaranteed.
Unit tampered with remotelyActual temperature measured by the sensor, not the one reported by the controllerSame as for an open doorThe actual temperature

During a power cut the refrigeration units stop too: the alert that the central unit is unreachable is the signal to act.

Independent measurement: KRYO measures, it does not operate the unit

Remotely managed refrigeration units can be tampered with remotely. A system that reads the temperature from the unit’s controller reads what the controller declares. KRYO measures it with its own sensors, inside the cold compartment, with no connection to the controls.

Independent measurement

KRYO sensors sit inside cold rooms and display cases, battery-powered and communicating over radio. They are not connected to the units’ control systems: they read the actual temperature, not the one declared by the controller.

No control over your units

No KRYO component can change thresholds, defrost cycles or settings on your units. It opens no new door into your refrigeration: the only connection is the network cable between the central unit and the router.

An alert whatever the cause

Open door, unit fault, abnormal defrost or remote tampering: if the temperature stays out of range, the alert goes out on Telegram and email, so you can act in time and reduce the risk of loss.

A recent case: on the night of 11–12 October 2026, a cyberattack remotely altered the refrigeration systems of more than 350 supermarkets in France, pushing temperatures up to 50 °C for hours before staff noticed (source: EuropaToday, 13 October 2026, based on data from Reuters and the Paris public prosecutor’s office).

Installation questions

Do I have to close the business to install it?
No. For the temperature kit, you plug one cable into the router and place the sensors, even during working hours. Only power meters at the electrical panel, if any, require a qualified electrician, to be scheduled.
My router is a long way from the cold rooms. Is that a problem?
Usually not: the central unit can sit next to the router and the sensors talk to it by radio. If your photos show critical distances or walls, we tell you beforehand; actual coverage is checked at activation in any case and, if a point is not covered, the sensor or the central unit is moved.
How long between delivery and activation?
As a guide, one day, if a network socket is available and radio coverage is confirmed at the initial check. If components need moving, work on the electrical panel is required or the network needs sorting out, a few days more: you see this beforehand, in the proposal.
If the power or the Internet goes down, what happens to the readings?
The service notices that the central unit is no longer reachable and alerts you. In the log, the period is shown as incomplete monitoring. Sensors and central unit can store readings during the outage; their automatic recovery into the log is still being validated and we do not guarantee it.
Do I need to use a computer or an app?
No. Alerts arrive on Telegram and email. The temperature log is available whenever you need it, for example during an inspection: it can be exported as a PDF per cold room and period, with an integrity fingerprint (SHA-256) kept in the log, which lets you verify that the document has not been altered after issue. It is not a qualified digital signature.
Can I keep the HACCP log I use today?
KRYO replaces manual temperature entries for the points it monitors. Your HACCP consultant can update the self-monitoring plan to state that temperatures are read and recorded automatically. The rest of the plan does not change.

The first step is a photo.

Send us photos of your cold rooms, fridges and router: we’ll tell you how to protect them, no obligation.

Assess monitoring for your cold rooms
Assess monitoring for your cold rooms