Automatic cold-chain control for businesses that store food and other cold-chain products · wireless sensors, pre-configured kit
Operational control of cold rooms · HACCP

Your stock in the cold room, protected even when nobody is there. It alerts you first, not the morning after.

An alert in time to act. The history ready for inspections. The energy use of every cold room in plain sight.

Wireless sensors inside cold rooms, fridges and display cases read temperature and humidity every 3–5 minutes. If a value stays out of range, KRYO alerts the people you nominate on Telegram and email, with what to check. Every reading stays in the history: the HACCP temperature log fills itself, within your self-monitoring plan. Door, energy and production room are monitored from the same service.

For gelato shops, pastry shops, bakeries, food production labs, restaurants, café-bars, hotels and food production sites · No obligation

kryo · night watch · restaurant ILLUSTRATIVE EXAMPLE
01:50KITCHEN CLOSED 5 control points · readings every 3–5 minutes
Telegram · KRYOowner · head of kitchen
Simulation with sample values, not real data. Thresholds and waiting times are set with you, around the normal cycles of each unit.

Example sequence: at 02:03 the meat cold room exceeds the threshold; after two consecutive out-of-range readings an Attention alert is sent; after 50 minutes above the threshold the Action required alert goes to the owner and manager; once back within limits, the non-conformity stays on record with date and time.

24/7readings every 3–5 minutes, even with the doors closed
0cables to run through your fridges
Same dayindicative activation of the temperature kit, after the network and coverage check
4 areascold room · door · energy · production room, with the same history and the same alerts
Where it is installed Cold roomsFrozen cold roomsFridgesFreezersRefrigerated display casesRefrigerated countersBlast chillers (holding mode)Gelato storage freezersRefrigerated cabinetsProving chambersCold storesProduction roomElectrical panel

Temperature alerts

How it works: a clear alert on Telegram and email, with a verdict and what to check

No charts to interpret. Three states, each with a rule you can read.

Measurement, transmission and alert are three separate steps: the sensor normally reads and transmits every 3–5 minutes; a temperature alert is triggered after at least two consecutive out-of-range readings, so roughly 6–10 minutes from the start of the anomaly, plus message delivery time. Brief door openings and normal defrost cycles do not trigger it.

From the cold compartment to your phone, in five steps

  1. The sensor measuresIn the cold compartment, close to the stock. Battery-powered, wireless, at regular intervals.
  2. Transmits by radioTo the central unit, connected to the router with a network cable.
  3. KRYO comparesEvery reading against the thresholds and waiting times set around the unit’s normal cycles.
  4. It alerts youIf a value stays out of range for several readings: what is happening and what to check, on Telegram and email.
  5. Stays in the logOnce back in range, all clear. The non-conformity stays on record, with date, time and duration.
All clear

All points within limits

No needless alerts. The log fills itself, silently. Every day, for every cold room, a verdict: compliant, compliant with remarks, non-compliant or incomplete monitoring.

How it is decided: all the cold room’s sensors transmit on schedule, and the readings are valid and within the threshold.

Attention

A value has just gone out of range

A door left open, a defrost cycle longer than usual. There is time to act, and it often recovers on its own.

How it is decided: at least two consecutive out-of-range readings. Brief door openings and normal defrost cycles do not count.

Action required

The problem persists

Alert to the nominated recipients, with what to check, and reminders until it is back in range. Escalation to a second contact is planned if nobody takes charge: we confirm it in the proposal.

How it is decided: the value stays out of range beyond the second waiting time, or a sensor or the central unit stops communicating beyond the time limit.

A silent sensor is never read as ‘All clear’: it triggers an alert just like an exceeded threshold, and the gap in readings is declared in the log. You can nominate several recipients, for example the owner and the head of kitchen or production room manager. What happens in every failure scenario →

What KRYO monitors

Cold room, door, energy and production room: one service, one history

Cold room temperature is the base. The other areas are activated with the configuration agreed in the proposal.

Every area produces the same kind of result: readings at regular intervals, an alert when a value stays out of range, and a record that stays. The readings below change to show how they appear: they are sample values, not real data.

Baseexample

Cold room: temperature and humidity

Chilled and frozen cold rooms, fridges, freezers, display cases, blast chillers in holding mode. Readings every 3–5 minutes, alert after two consecutive out-of-range readings, each non-conformity recorded with start, end and duration, daily verdict per cold room. Sensor range −30 °C to +70 °C and 0 to 100 % relative humidity, non-condensing. The sensor →

−18.6 °C68 % RHall clearfrozen cold room · threshold −18 °C
Availableexample

Door: openings and closings

A sensor on the cold room door records every opening and closing, with time and duration. If the door stays open beyond the time you set with us, a dedicated alert is sent, before the temperature rises. In the history you see how often and for how long each cold room is opened.

CLOSEDlast opening 2 minall clearcold room 1 door · threshold 5 min
Availableexample

Energy: consumption of every cold room

Single-phase or three-phase power meters, per cold room or in the panel. You see the power draw and the trend over time: running times getting longer, consumption outside opening hours, cold rooms that consume more than others for the same workload. To be read alongside temperature and with whoever does your maintenance. Details →

430 Wpower draw while runningall clearcold room 1 · single-phase meter
Availableexample

Production room: ambient temperature and humidity

The room sensor measures temperature and relative humidity in processing and ambient-temperature storage areas: production room, dry store, proving area. Thresholds follow your self-monitoring plan; alerts arrive on the same channels as the cold rooms. It is not a microbiological control.

21.4 °C52 % RH · threshold 25 °C / 65 %all clearproduction room · room sensor

Base: included in every configuration · Available: activated with dedicated sensors, as per the proposal

Everything in one history

Temperature, door openings and power draw of a cold room are viewed together, on the same timeline. When a cold room warms up you can see whether the door was open and how the unit was running, without piecing together three different tools.

What KRYO does and what stays with you

KRYO puts the data side by side and alerts you when a value goes out of range. It does not attribute the cause of an anomaly on its own: interpretation stays with you and whoever does your maintenance, with measured data instead of guesswork. In the same service, expiry-date labels.

When KRYO makes the difference

Five real situations, from event to action

For each case: what is detected, what you receive, what you check, what you can do. Data and messages are illustrative examples.

Temperature out of range with the doors closed

  1. Event detectedMeat cold room at +5.8 °C at 02:11, two consecutive readings above the +4 °C threshold.
  2. AlertOn Telegram and email to the owner: value, how long for, what to check. If it continues, ‘Action required’ to the manager as well.
  3. CheckFrom the history you see whether the door shows as open and whether the unit was drawing power as usual.
  4. Possible actionWhoever receives the alert decides whether to act or call someone out; once back in range, the non-conformity stays on record with date, time and duration.

Door left open beyond the set time

  1. Event detectedCold room 2 door open for 6 minutes, configured threshold 5 minutes, during morning loading.
  2. AlertDedicated door message, before the temperature goes out of range.
  3. CheckIn the door-opening history you see the time, the duration and how many times it happened that week.
  4. Possible actionClose the door, review the loading procedure or the threshold with us.

What happened last night

  1. Information availableFor every cold room, the day’s verdict: compliant, compliant with remarks, non-compliant, incomplete monitoring.
  2. ReviewThe reading history, door openings and power draw trend on the same timeline.
  3. CheckIf there was an excursion: when it started, how long it lasted, the peak value.
  4. Possible actionDecide on the stock with measured data; export the PDF report for your consultant or for an inspection.

Monitoring a cold room’s consumption

  1. Event detectedFor several days the frozen cold room has been running longer than in previous weeks, with temperature within limits.
  2. Information availableDay-by-day power draw trend, compared with the previous period.
  3. CheckAgainst the same cold room’s temperature and door openings: load, season, openings, or something that needs looking at.
  4. Possible actionSchedule a check with whoever does your maintenance, instead of waiting for the breakdown. KRYO does not identify the cause: it provides the data.

Production room conditions

  1. Event detectedProduction room temperature at 27 °C in the afternoon, above the 25 °C threshold in the self-monitoring plan; humidity at 70 %.
  2. AlertOn the same channels as the cold rooms, to the production room manager.
  3. CheckThe history shows what time the rise begins and whether it repeats every day.
  4. Possible actionAdjust the air conditioning or how processing is organised; the data remains on record in support of the self-monitoring plan.

Want to see how an alert arrives?

A real example of the sequence: Attention, Action required, back in range and the day’s verdict.

KRYO measures and alerts. It does not operate the refrigeration units and does not replace the person who receives the alert: acting on it remains your job, or that of the people you nominate.

The problem

Lost stock and HACCP non-conformities: the risk is finding out too late

The risk is not the anomaly. It is noticing it when it is too late.

At night

An anomaly at 2:00 is only discovered at opening time. By then the stock is compromised.

On closing days

Thirty hours or more with nobody watching. A door not properly closed can be enough to compromise the stock.

During an inspection

A handwritten log does not document what happened between one reading and the next.

A paper log and a thermometer read twice a day capture a single instant. The rest of the time, nobody is watching.

Do the maths

How many hours a week is your cold chain left unwatched?

Enter your numbers. The calculation stays on your device: we save nothing.

unwatched hours · typical week168 HOURS
96unwatched hours a week

That is 57% of the time.

BUSINESS OPENUNWATCHED

If an anomaly starts in those hours, you find out at opening time. Or you find out first.

How it works

How KRYO monitoring works: from photos to activation

Three steps. For the temperature kit, normally with no technician on site.

Send us your photos

Cold rooms, fridges and where the router is: we use them for a preliminary assessment of the points to monitor and of coverage.

Receive the pre-configured system

Central unit and sensors arrive already set up for your business.

Check and activation

One network cable and the sensors in place; at the initial check we confirm coverage and positions. Typically same day, if network and coverage allow.

All the details →

Installation

What is installed: a central unit at the router and battery sensors in the cold rooms

No cables in the fridges, no building work. For the temperature kit, normally with no technician on site.

You do not need to understand sensors, networks or software. The central unit arrives pre-configured on the basis of the photos of your premises: you connect it to the router with a network cable, place the sensors inside cold rooms and display cases, and at the initial check we verify remotely that everything is transmitting. The unit uses your business network, with no SIM card.

  • No building workNo drilling, chasing or work on the refrigeration units.
  • Temperature kit with no technician on siteWhen the installation conditions allow: one network cable and the sensors in place. Any power meters in the electrical panel require qualified personnel.
  • Independent of Wi-FiThe central unit uses the network cable; the sensors use long-range, low-power radio. We estimate coverage from the photos and confirm it at activation.
  • Indicative same-day activationAfter delivery, if a network socket is available and radio coverage is confirmed; otherwise a few more days, and you know in advance.
  • The sensor in the right placeThe temperature inside a cold room is not uniform: it varies between door and back wall, between shelves, after every opening. From the photos we propose the spot, close to the stock and away from the cold air outlet; we confirm it at activation.
typical setup · restaurantWIRELESS
Battery-powered radio sensorstemperature and humidity in cold rooms, fridges, display cases, blast chillers · inside the cold compartment
BATTERY-POWERED
Central unitone network cable to the router · pre-configured for your business
PRE-CONFIGURED
Alerts and logTelegram · email · automatic HACCP log, with PDF report and integrity fingerprint
24/7
Door, energy, production room, labelsdoor sensors · power meters per unit or in the panel (single-phase and three-phase) · room sensor (temperature and humidity) · label printer
SAME HISTORY

By sector

Every business has its own critical points. The service is configured around them.

Gelato shops and pastry shops, bakeries and food production labs, restaurants, café-bars and hotels, production sites: different problems, scenarios and questions, the same continuous watch.

What you are buying

What you get with KRYO: central unit, sensors and a continuous watch service

A kit pre-configured for your business and a service that continues every day.

In the box
  • Central unit, pre-configured, to be connected to the router with a network cable
  • Wireless, battery-powered temperature and humidity sensors, already paired: one for every unit to be monitored
  • According to the agreed configuration: door sensors, power meters per unit or in the electrical panel (single-phase and three-phase), room sensor for the production room (temperature and humidity), label printer
In the service, every day
  • Readings at regular intervals, 24 hours a day, even with the doors closed
  • Telegram and email alerts to the recipients you nominate, with the verdict and what to check
  • HACCP temperature log that fills itself, with a daily verdict per cold room and PDF report with integrity fingerprint
  • Remote check that every sensor is transmitting; remote support; thresholds reviewed with you whenever something changes

Build your monitoring setup

Tell us how many units you want to keep under control. The kit is put together for you; you receive the price with the proposal, after the photos.

your continuous watch · compositionKIT

Each unit is a control point with its own threshold and its own waiting time. Large cold rooms may need a second sensor: we estimate this from your photos and confirm it at activation. The final configuration is set out in the proposal; further sensors can be added later.

HACCP software and automatic monitoring

Digital HACCP log or automatic temperature monitoring: what’s the difference

HACCP software digitises your procedures. KRYO takes the measurements itself and hands you the evidence. The two can work side by side.

HACCP software and digital logs

They digitise the procedures

  • Manuals, record sheets and entries move from paper to screen
  • The temperature is read and entered by a person
  • If nobody is looking, the anomaly is only found afterwards

KRYO

Measures automatically, 24 hours a day

  • Wireless sensors read the temperature at regular intervals
  • The temperature log fills itself in
  • Alert on Telegram and email while the problem is happening
HACCP temperature log: paper, manual-download data logger, alarm thermometer or automatic monitoring
NeedPaper logManual-download data loggerAlarm thermometerKRYO (automatic monitoring)
Alert when the premises are closedNoNo: the data is only seen when someone downloads itOnly if someone hears itYes, on your phone, while the problem is happening
Temperature logBy handYes, after downloadNoDigital and automatic, with a daily verdict
Alert if a sensor stops working—No, you only find out at downloadNoYes
Doors, energy consumption and room climate———In the same service and the same history
Product labels and expiry datesBy hand, from memory——Printed, in the database, with an alert before expiry
Handling non-conformitiesManualReconstructed afterwardsNoneTracked with date, time and duration
Staff time requiredDailyPeriodic, for the downloadLowNone for taking readings

Already using HACCP software or a consultant? KRYO does not replace them: it works alongside your procedures and provides measured temperatures, not declared ones. Information for HACCP consultants →

Labels and expiry dates · in preparation

Printed HACCP labels and expiry dates under control: the inventory of every cold room, with alerts

No handwritten labels. No expiry dates kept in your head.

After temperature monitoring, as part of the agreed configuration: a printer for the labels on products in your cold rooms and fridges, with name, preparation or opening date, expiry date and location. Every label goes into the database, the inventory of each cold room updates itself and, before a product expires, an alert arrives on the same channels as the temperature alerts. Below is an illustrative demo.

1. You prepare and print name, date, expiry date, location.
2. The inventory updates for each cold room, sorted by expiry date.
3. You remove the product: the removal stays on record, with date and time.
try a labelILLUSTRATIVE EXAMPLE
· today

The shelf lives shown are examples: you set your own, according to your self-monitoring plan. No data is saved.

Inventory · cold rooms and fridges · sorted by expiry date

Label log: every print and every product removed stays on record, with date and time.

Telegram · KRYOevening expiry alert

Monitoring and record-keeping obligations

KRYO helps you meet the HACCP obligations that apply to you. It does not replace them.

Regulation (EC) No 852/2004 requires every food business to have procedures based on HACCP principles, to maintain the cold chain and to control temperatures, with records “where appropriate”, proportionate to the business. For quick-frozen foods, Regulation (EC) No 37/2005 adds specific requirements on recording instruments; gelato and ice cream are not classed as quick-frozen foods. Automatic monitoring is not compulsory for everyone, and KRYO on its own does not guarantee HACCP compliance: it provides measurements, alerts and verifiable records for the temperature-related control points, within your self-monitoring plan. The plan, the critical limits and the corrective actions remain yours and your consultant’s.

Measured evidence

Taken inside the cold compartment, at regular intervals, by a sensor independent of the refrigeration unit. Not declared, not transcribed by hand, not reconstructed the next day.

Verifiable evidence

Every reading carries its date, time and source sensor and cannot be edited or deleted from the interface; every threshold change is tracked. The PDF report has an integrity fingerprint (SHA-256) kept in the log.

Evidence ready to hand

The alert when a value stays out of range, the report when the inspector asks for it, the verdict for every day and every cold room.

Guide to HACCP temperatures, with sources and the requirements for quick-frozen foods → · Who is behind KRYO and what we don’t do →

KRYO is a service of ABK S.r.l.s., Bari. We do not offer HACCP consultancy or refrigeration maintenance: the temperatures we provide are measured, not declared, and we work alongside your consultant with no conflict of interest.

FAQ

Frequently asked questions on automatic cold-chain control and HACCP obligations

Thermometer, data logger or remote monitoring: what’s the difference?
A thermometer shows the current value to whoever is looking at it. A data logger saves the readings, but you only see them when someone downloads them: the anomaly is only found afterwards. Remote monitoring transmits the readings at regular intervals to a service that compares them with the thresholds and alerts the right people while the problem is happening, keeping the history. That is what KRYO does, with readings every 3–5 minutes. The guide →
Does the sensor measure the air temperature or the food temperature?
The air inside the cold room, at the point where it is placed. Food changes temperature more slowly than air: a brief door opening raises the air by a few degrees without affecting the product, while a long excursion compromises it. That is why alerts are triggered after several consecutive out-of-range readings, and the daily verdict weighs the duration of each excursion. Core product temperature remains a probe measurement, where the self-monitoring plan requires it.
Why monitor door openings?
The door is the leading cause of avoidable excursions: long openings during loading, a seal that no longer holds, a door someone forgot to close. With the door sensor you see when and for how long each cold room is opened, and you receive an alert if it stays open beyond the time you have set, before the temperature goes out of range. In the history, door openings and temperature sit on the same timeline.
How do I read a cold room’s energy consumption?
As a trend, not as a bill: how much the cold room draws, how long it runs, how that compares with previous weeks, what it consumes when the premises are closed. Rising consumption for the same workload is something to put to whoever does your maintenance, together with the temperature and the door openings. KRYO makes the data visible; it does not attribute the cause on its own. Details →
What happens if the internet or the power goes down?
The service detects that the central unit is no longer reachable and alerts you; in the log, that period is recorded as incomplete monitoring, never as ‘All clear’. The battery sensors keep measuring and store their readings locally, as does the central unit; the automatic recovery of those readings into the log after restoration is confirmed in the proposal. During a blackout the refrigeration units are down too: the alert is your signal to act.
Who receives the alerts, and who has to act?
Alerts go out on Telegram and email to the people you nominate, for example the owner and the production room manager or head of kitchen, together with what to check; WhatsApp support is coming. Acting on them remains the recipients’ responsibility: KRYO does not operate the refrigeration units and is not an emergency call-out service. Escalation to a second contact is planned for when nobody takes charge of the alert: we confirm it, with timings, in the proposal.
Does KRYO make me HACCP compliant?
KRYO helps you meet the temperature monitoring and record-keeping obligations that apply to your business, as a service integrated into your self-monitoring plan. The plan, the critical limits and the corrective actions remain yours and your consultant’s: KRYO provides measurements, alerts and verifiable records, not automatic compliance. What the regulation requires →
Is automatic temperature monitoring mandatory?
Not for everyone. Regulation (EC) No 852/2004 requires temperatures to be controlled and, where appropriate, recorded, in line with the self-monitoring plan. For quick-frozen foods, Regulation (EC) No 37/2005 requires recording instruments that comply with technical standards, with some exemptions; gelato is not classed as a quick-frozen food. What applies to you depends on your products, processes and self-monitoring plan.
Do I need a technician to install it? How quickly is it up and running?
For the temperature kit, in most cases no: it arrives pre-configured on the basis of your photos; you connect the central unit to the router with a network cable and place the wireless sensors. Radio coverage and positions are confirmed at the initial check: activation typically happens the same day, after delivery, if network and coverage allow. Power meters in the electrical panel require qualified personnel.
Do I have to manage a platform or an app?
No. Alerts arrive on Telegram and email; the history and the PDF report are available whenever you need them, for example during an inspection or for your consultant.
How much does it cost?
It depends on how many cold rooms you have and which areas you activate. You start with the free assessment: tell us your type of business, number of cold rooms and main need, and you receive a tailored proposal.
Where do you operate?
KRYO was founded in Apulia and mainly serves businesses in southern Italy. The system is shipped pre-configured and support is remote, so businesses in other regions can activate it too.

Free assessment

Assess monitoring for your cold rooms.

Four pieces of information are enough: type of business, number of cold rooms, main need and a contact detail. We get back to you, ask for a few photos of your cold rooms, fridges and router, and tell you what to monitor and how, before any proposal. Coverage and sensor positions are confirmed at activation.

Why it’s free: without understanding how you work and without seeing your cold rooms and router, we cannot tell you what you really need. The assessment is as useful to us as it is to you.

  • No commitmentYou receive the proposal, you decide.
  • A tailored answerPoints to monitor, recommended thresholds and a proposal.

Prefer to email? [email protected]

Want to add your name, town, photos or details? (optional)

The photos are for the preliminary assessment: radio coverage and sensor positions are checked at activation.

No obligation · We get back to you ourselves, not a call centre.

Prefer to email? [email protected] ·

Assess monitoring for your cold rooms